CHI07MA083

The fatigue failure of the tail rotor blade root fitting due to a manufacturing defect which resulted in the separation of the tail rotor system and loss of tail rotor control. A contributing factor to the accident were the trees that the helicopter struck during the autorotation.

The helicopter pilot reported that he was conducting a Part 135 air tour flight with 4 passengers on board the helicopter. The helicopter was about 1,500 feet above ground level with about 80 - 85 knots of airspeed when within a split-second he heard two loud "bangs." The nose of the helicopter pitched down and the helicopter yawed to the right. He applied left pedal but without effect. He attempted to "get more forward airspeed," but each time he did the helicopter nosed over and yawed to the right. The right yaw developed into a tight spin, and he realized that he "lost his tail rotor." The pilot executed an autorotation to a clearing located at a campground. The helicopter impacted the trees at the western edge of the clearing during the autorotation. The helicopter impacted the terrain on its right, front side. Inspection of the helicopter revealed that the tail rotor output shaft and the tail rotor blades separated from the tail rotor gearbox. The tail rotor assembly was inspected at the National Transportation Safety Board's Materials Laboratory. The inspection revealed that the tail rotor blade assembly fractured through the root fitting in the general area that coincided with a hole for the blade retention bolt. The root fitting contained a 1-inch nominal diameter longitudinal hub bore with a tapered (conical) hole bottom. A relief radius was located between the hub bore and the conical hole bottom. The inspection revealed crack arrest marks typical of a fatigue cracking that emanated from multiple origins at the relief radius between the hub bore and conical hole bottom. The relief radius measured approximately 0.001 inch, much less than specified by the engineering drawing (0.12 inch and 0.15 inch). On April 26, 2007, McDonnell Helicopters, Inc. (MDHI) issued mandatory Service Bulletin (SB) 369D-204, 369E-099, 369F-084, 369H-247, titled "Tail Rotor Blade Assembly, One Time Inspection." According to MDHI SB, before further flight, the tail rotor should be removed from helicopter models 369 (Army YOH-6A), 369 (Army OH-6A), 369H, 369HM, 369HS, 369HE, 369D, 369E, 369F, and 369FF. The hub bore should be visually examined with a flashlight. If the relief radius does not contain a smooth transition between the bore and conical bottom hole, the root fitting should be removed from service. On April 27, 2007, the Federal Aviation Administration issued emergency Airworthiness Directive (AD) 2007-09-51 that mandated inspection of the root fittings per the MDHI SB.

HISTORY OF FLIGHT On March 11, 2007, at 1259 Hawaiian Standard Time, a McDonnell Douglas (MD) 369FF helicopter, N911VC, operated by Smoky Mountain Helicopters and doing business as Inter-Island Helicopters Inc., sustained substantial damage when it impacted trees and terrain in the town of Haena on the island of Kauai, Hawaii, during a Part 135 commercial air tour flight. The flight departed from the Port Allen Airport (PAK), Hanapepe, Hawaii, on a 55-minute sightseeing tour of Kauai. During cruise flight near Tunnel Beach in Haena, the tail rotor output shaft and the tail rotor blades separated from the tail rotor gearbox and fell into the ocean. The pilot executed an autorotation to a YMCA campground that was located next to the beach. The pilot received minor injuries; however, the right front seat passenger was killed, and the three other passengers received serious injuries. Visual meteorological conditions prevailed and a company flight plan was in effect. The pilot stated that he reported for duty one hour prior to his first flight of the day that was scheduled for 0800. He conducted a thorough preflight of the aircraft that included an inspection of the tail rotor section. The fluid levels were normal and there were no signs of cracks, dings, or delamination of the surface and leading edges of the tail rotor blades. The pitch change links were in good condition and no loose bearings were noted. He reported that the tail rotor gearbox housing appeared to be in good condition and no cracks were observed. He checked the nuts that hold the tail rotor section in place. The torque seal was visible on each nut, and he physically checked each one to determine if they were tight. The bellcrank was not cracked, the nuts were tight, and the cotter pins were in place. The pilot reported that the first two flights of the day, the first at 0800 and the second at 1005, were "waterfall" flights. During the waterfall flights, he flew to a private landing zone located near a waterfall. While in the landing zone, he shut the helicopter down while the passengers visited the waterfall for about 45 minutes. He reported that he conducted a post flight inspection "as we always do." He checked the fluid levels of the engine, main rotor transmission, and the tail rotor gearbox. The fluid levels were normal and no leaks were noted. He checked the main rotor and tail rotor blades for cracks, dings, and delamination of the surface and leading edges of the blades. During both flights, the helicopter operated normally and no abnormal vibrations were noted. The third flight was a 50 to 55-minute island tour that departed about 1210. The pilot reported, "I viewed the passengers that got on board, jackets were on, zipped up and secured, life jacket pouches were on and secured, cameras were secured, and they had no hats or bags with them." He reported that during the accident flight he felt no abnormal vibrations in the controls. About halfway through the flight, he was flying over Tunnel Beach, about 50 yards from the shoreline, at 1,000 feet above ground level (agl) with 80 - 85 knots of airspeed. Within a split-second, he heard two loud "bangs" and he "felt it" in his seat and pedals. The nose of the helicopter pitched down, and the helicopter yawed to the right. He applied left pedal but without effect. He attempted to "get more forward airspeed," but each time he did the helicopter nosed over and yawed to the right. The right yaw developed into a tight spin, and he realized that he "lost his tail rotor." He adjusted the collective and throttle to get the "yaw under control," and reported that, "it did slow down the yaw a little." He recognized the YMCA campground and decided to execute an autorotation to the open field at the campground. He entered the autorotation by rolling off the throttle and lowering the collective. He reported the "right yaw slowed even more." He attempted to gain airspeed and he "followed the right yaw," which made the spin slower, as he approached the campground. When the helicopter was about five feet agl, he pulled the collective up to cushion the landing. After the helicopter impacted the terrain, he checked the condition of each passenger, and then secured the engine by turning the master switch off and pulling the fuel shutoff. He took the fire extinguisher and exited the helicopter. He saw that the tail rotor blades and output shaft had separated from the tail rotor gearbox. Local citizens arrived at the accident site almost immediately to provide assistance to the pilot and passengers. Within minutes, the local police and fire department personnel were on site. There were numerous witnesses to the accident. One witness reported that she heard a loud "pop" and she saw two objects falling into the ocean. The larger object fell into the ocean close to shore. The other object "fell slower in a fluttering action." She reported that both objects fell into the ocean where the waves were breaking and the reef ended. Another witness heard a "pop" and observed the helicopter spiraling down. She reported, "Then the spiral tightened and sped up. The overhead rotor could be seen as blades (not turning). The blue and white body of the copter was turning slowly around the rotor - rather flat - no obvious pitch of the nose up or down. There was a large thud - presumably impact." A third witness reported that the helicopter "started a slow spiral to the right as it was circling a house" and that the "spiral tightened up and there were two of these tight spirals - the main blades were not turning very rapidly." He reported that at "no time was the nose significantly down. It was a gradual descent but not in a violent down descent. It did a total of 3 spirals - one gradual and the last 2 were more rapid." The three passengers on board the helicopter were interviewed. They reported that they did not see anything fall out of the helicopter prior to the accident, and they did not observe birds in the area. PERSONNEL INFORMATION The pilot was a 30-year-old commercial pilot with helicopter and instrument (helicopter) ratings. He held a second-class medical certificate that was issued in January 2007. He reported a total of 2,041 flight hours with 189 hours in the MD 369FF helicopter. AIRCRAFT INFORMATION The helicopter was a MD Helicopter 369FF manufactured in 1987. It was equipped with a turbine-powered Allison 250-C30 engine. At the time of the accident, the total helicopter time was about 7,800.8 flight hours. The most recent airframe inspection was a 100-hour inspection completed on February 28, 2007, at a total airframe time of 7,775.8 hours. The last annual inspection was completed on July 9, 2006, at a total airframe time of 7,098.0 hours. The last inspection of the engine was a 150-hour inspection completed on February 11, 2007, at a Hobbs time of 4,174.2 and an engine time of 7,400.2 hours. METEOROLOGICAL INFORMATION The observed surface weather at the Lihue Airport, Lihue, Hawaii, located about 17 miles southeast of the accident site, was: Wind 010 at 4 knots, scattered clouds at 2,800 feet, overcast 3,700 feet, temperature 23 degrees Celsius (C), dew point 18 degrees C, altimeter 29.94 inches of mercury. WRECKAGE AND IMPACT INFORMATION The helicopter impacted the trees and terrain at the western edge of the YMCA campground at coordinates 22 degrees 13.412 minutes north latitude, 159 degrees 33.231 minutes west longitude. The entire helicopter wreckage was located at the impact site, except for the tail rotor output shaft and tail rotor blades. A broken tree limb about 15 - 20 feet above the ground was visible in the trees located next to the wreckage. There was no ground fire. The inspection of the airframe revealed extensive damage to the fuselage with major damage concentrated at the underside of the lower right